ObjectiveTo discuss the influence of artificial ankle elastic improved inserts (hereinafter referred to as “improved inserts”) in reducing prosthesis micromotion and improving joint surface contact mechanics by finite element analysis. Methods Based on the original insert of INBONE Ⅱ implant system (model A), four kinds of improved inserts were constructed by adding arc or platform type flexible layer with thickness of 1.3 or 2.6 mm, respectively. They were Flying goose type_1.3 elastic improved insert (model B), Flying goose type_2.6 elastic improved insert (model C), Platform type_1.3 elastic improved insert (model D), Platform type_2.6 elastic improved insert (model E). Then, the CT data of right ankle at neutral position of a healthy adult male volunteer was collected, and finite element models of total ankle replacement (TAR) was constructed based on model A-E prostheses by software of Mimics 19.0, Geomagic wrap 2017, Creo 6.0, Hypermesh 14.0, and Abaqus 6.14. Finally, the differences of bone-metal prosthesis interface micromotion and articular surface contact behavior between different models were investigated under ISO gait load. Results The tibia/talus-metal prosthesis interfaces micromotion of the five TAR models gradually increased during the support phase, then gradually fell back after entering the swing phase. The improved models (models B-E) showed lower bone-metal prosthesis interface micromotion when compared with the original model (model A), but there was no significant difference among models A-E (P>0.05). The maximum micromotion of tibia appeared at the dome of the tibial bone groove, and the micromotion area was the largest in model A and the smallest in model E. The maximum micromotion of talus appeared at the posterior surface of the central bone groove, and there was no difference in the micromotion area among models A-E. The contact area of the articular surface of the insert/talus prosthesis in each group increased in the support phase and decreased in the swing phase during the gait cycle. Compared with model A, the articular surface contact area of models B-E increased, but there was no significant difference among models A-E (P>0.05). The change trend of the maximum stress on the articular surface of the inserts/talus prosthesis was similar to that of the contact area. Only the maximum contact stress of the insert joint surface of models D and E was lower than that of model A, while the maximum contact stress of the talar prosthesis joint surface of models B-E was lower than that of model A, but there was no significant difference among models A-E (P>0.05). The high stress area of the lateral articular surface of the improved inserts significantly reduced, and the articular surface stress distribution of the talus prosthesis was more uniform. Conclusion Adding a flexible layer in the insert can improve the elasticity of the overall component, which is beneficial to absorb the impact force of the artificial ankle joint, thereby reducing interface micromotion and improving contact behavior. The mechanical properties of the inserts designed with the platform type and thicker flexible layer are better.
Objective To investigate whether human amniotic mesenchymal stem cells (hAMSCs) have the characteristics of mesenchymal stem cells (MSCs) and the differentiation capacity into ligament fibroblastsin vitro. Methods The hAMSCs were separated through trypsin and collagenase digestion from placenta, the phenotypic characteristics of hAMSCs were detected by flow cytometry, the cytokeratin-19 (CK-19) and vimentin expression of hAMSCs were tested through immunofluorescence staining. The hAMSCs at the 3rd passage were cultured with L-DMEM/F12 medium containing transforming growth factor β1 (TGF-β1) and vascular endothelial growth factor (VEGF) as the experimental group and with single L-DMEM/F12 medium as the control group. The morphology of hAMSCs was observed by inverted phase contrast microscope; the cellular activities and ability of proliferation were examined by cell counting kit-8 (CCK-8) method; the ligament fibroblasts related protein expressions including collagen type I, collagen type III, Fibronectin, and Tenascin-C were detected by immunofluorescence staining; specific mRNA expressions of ligament fibroblasts and angiogenesis including collagen type I, collagen type III, Fibronectin, α-smooth muscle actin (α-SMA), and VEGF were measured by real-time fluorescence quantitative PCR. Results The hAMSCs presented monolayer and adherent growth under inverted phase contrast microscope; the flow cytometry results demonstrated that hAMSCs expressed the MSCs phenotypes; the immunofluorescence staining results indicated the hAMSCs had high expression of the vimentin and low expression of CK-19; the hAMSCs possessed the differentiation ability into the osteoblasts, chondroblasts, and lipoblasts. The CCK-8 results displayed that cells reached the peak of growth curve at 7 days in each group, and the proliferation ability in the experimental group was significantly higher than that in the control group at 7 days (P<0.05). The immunofluorescence staining results showed that the expressions of collagen type I, collagen type III, Fibronectin, and Tenascin-C in the experimental group were significantly higher than those in the control group at 5, 10, and15 days after culture (P<0.05). The real-time fluorescence quantitative PCR results revealed that the mRNA relative expressions had an increasing tendency at varying degrees with time in the experimental group (P<0.05). The relative mRNA expressions of collagen type I, collagen type III, Fibronectin, α-SMA, and VEGF in the experimental group were significantly higher than those in the control group at the other time points (P<0.05), but no significant difference was found in the relative mRNA expressions of collagen type I, collagen type III, and VEGF between 2 groups at 5 days (P>0.05). Conclusion The hAMSCs possesses the characteristics of MSCs and good proliferation ability which could be chosen as seed cell source in tissue engineering. The expressions of ligament fibroblasts and angiogenesis related genes could be up-regulated, after inductionin vitro, and the synthesis of ligament fibroblasts related proteins could be strengthened. In addition, the application of TGF-β1 and VEGF could be used as growth factors sources in constructing tissue engineered ligament.