Objective To analyze the relationship between the collateral ligament attachment and the epicondylar axis with rotational alignment of the femoral component in the total knee arthroplasty(TKA).Methods Twenty normal cadaver knee joints were anatomized and 2 holes were drilled on the distal femur from the deep and superficial insertions of the medial collateral ligaments to the lateral condylar part, respectively. Then, all the knees were scanned by MRI on the sagittal plane, making the drilled hole located relatively to the posterior condylar joint surface on the axial plane, and the posterior condylar angle (PCA) and thecondylar twist angle (CTA) were measured.Results The colateral ligament had the deep and superficial parts, and the deep part was strained during the knee flexing. PCA and CTA were 4.50±1.26° and 7.10±0.30° respectively, and there was a significant difference between them(P＜0.05), which were significantly greater than those reported abroad. On the sagittal plane, there wasno significant difference between the radiuses of the posterior medial and lateral condylar circles (Pgt;0.05). The distance from the center of the posterior condylar circle to the deep insertion of the medial collateral ligament (MCL) (d1) was 4.22±0.20 mm, and the distance to the superficial insertionof MCL (d2) was 7.36±0.13 mm. The difference between d1 and d2 was significant(Plt;0.05). Conclusion The center of the posterior condylar circle passes from the deep insertion of the collateral ligament, which can be regarded as a fixed flexionextension axis of the knee. By releasing the different parts of the collateral ligaments, the balance of the flexion and extension gap canbe obtained, and then varus, valgus or flexed contracture deformity of the kneecan be realigned. Besides, the rotational orientation of the femoral prothesis can be made by a reference to the epicondylar insertion of the collateral ligament.
Objective To investigate the effects of percutaneous cement discoplasty (PCD) and percutaneous cement interbody fusion (PCIF) on spinal stability by in vitro biomechanical tests. Methods Biomechanical test was divided into intact (INT) group, percutaneous lumbar discectomy (PLD) group, PCD group, and PCIF group. Six specimens of L4, 5 (including vertebral bodies and intervertebral discs) from fresh male cadavers were taken to prepare PLD, PCD, and PCIF specimens, respectively. Before treatment and after the above treatments, the MTS multi-degree-of-freedom simulation test system was used to conduct the biomechanical test. The intervertebral height of the specimen was measured before and after the axial loading of 300 N, and the difference was calculated. The range of motion (ROM) and stiffness of the spine in flexion, extension, left/right bending, and left/right rotation under a torque of 7.5 Nm were calculated. Results After axial loading, the change of intervertebral height in PLD group was more significant than that in other three groups (P<0.05). Compared with INT group, the ROM in all directions significantly increased and the stiffness significantly decreased in PLD group (P<0.05). Compared with INT group, the ROM of flexion, extension, and left/right rotation in PCD group significantly increased and the stiffness significantly decreased (P<0.05); compared with PLD group, the ROM of flexion, extension, and left/right bending in PCD group significantly decreased and the stiffness significantly increased (P<0.05). Compared with INT group, ROM of left/right bending in PCIF group significantly decreased and stiffness significantly increased (P<0.05); compared with PLD group, the ROM in all directions significantly decreased and the stiffness significantly increased (P<0.05); compared with PCD group, the ROM of flexion, left/right bending, and left/right rotation significantly decreased and stiffness significantly increased (P<0.05). Conclusion Both PCD and PCIF can provide good biomechanical stability. The former mainly affects the stiffness in flexion, extension, and bending, while the latter is more restrictive on lumbar ROM in all directions, especially in bending and rotation.
A three-dimensional finite element model of premaxillary bone and anterior teeth was established with ANSYS 13.0. The anterior teeth were fixed with strong stainless labial archwire and lingual frame. In the horizontal loading experiments, a horizontal retraction force of 1.5 N was applied bilaterally to the segment through hooks at the same height between 7 and 21 mm from the incisal edge of central incisor; in vertical loading experiments, a vertical intrusion force of 1.5 N was applied at the midline of lingual frame with distance between 4 and 16 mm from the incisal edge of central incisor. After loading, solution was done and displacement and maximum principle stress were calculated. After horizontal loading, lingual displacement and stress in periodontal membrane (PDM) was most homogeneous when the traction force was 14 mm from the edge of central incisor; after vertical loading, intrusive displacement and stress in PDM were most homogeneous when the traction force was 12 mm from the incisal edge of central incisor. The results of this study suggested that the location of center of resistance (CRe) of six maxillary anterior teeth is about 14 mm gingivally and 12 mm lingually to incisal edge of central incisor. The location can provide evidence for theoretical and clinical study in orthodontics.
摘要:目的:研究生物降解聚DL乳酸(PDLLA)自锁式捆绑带固定骨折的生物力学性能。方法:80只新西兰大白兔随机分为两组,建立股骨干非负重骨折动物模型,应用生物降解自锁式捆绑带固定骨折为实验组,钢丝固定骨折为对照组,分别于术后1、4、8、12周行生物力学检查进行比较。结果:捆绑带组在术后4、8、12周均比钢丝组的弯曲强度高,但4周、12周时Pgt;005,无统计学差异,8周时Plt;005,提示有统计学差异。离体同种固定物不同时间段抗拉强度自身比较:钢丝固定术后4阶段抗拉强度比较Pgt;005,任何两两比较都没有统计学差异,抗拉强度未随术后时间延长发生明显下降。捆绑带固定术后4周与术后1周比较Pgt;005,抗拉强度无明显降低,但术后8周和术后12周时Plt;005,抗拉强度明显下降。结论:生物降解自锁式捆绑带在非负重骨折治疗中可发挥良好的固定作用。生物降解自锁式捆绑带降解时,应力传导促进了骨折的愈合。Abstract: Objective: To study the biomechanics function of selflocking cerclage band made of biodegradable material polyDLlactic acid (PDLLA) in the fixation of fractures. Methods: Eighty rabbits were divided into two groups. Femur fracture models were made. Fractures were fixed using biodegradable selflocking cerclage band in experimental group and metal fixation material in control group. The biomechanics was analyzed and compared after 1, 4, 8 and 12 weeks respectively． Results: The bending strength of experimental group is more ber than that of control group after 4, 8 and 12 weeks, but it was not statistically significant at 4 and 12 weeks (Pgt;005). It was statistically significant at 8 weeks (Plt;005). The tensile strength of the same cerclage instrument was compared at different stage in vitro, and the result of the control group was not statistically significant at the four stage (〖WTBX〗P〖WTBZ〗gt;005). Regarding the changes of tensile strength of the cerclage instrument at different stage, the result of the experimental group was not statistically significant after 1 and 4 weeks (Pgt;005). However, the decrease of tensile strength was statistically significant after 8 and 12 weeks (Plt;005). Conculsion: Biodegradable selflocking cerclage band could be used in thetreatment of nonweightbearing fractures. The stress force conducting promotes healing of fracture when the selflocking biodegradable cerclage band degrades.
Objective To establish a finite element model of the knee joint based on coronal plane alignment of the knee (CPAK) typing method, and analyze the biomechanical characteristics of different types of knee joints.Methods The finite element models of the knee joint were established based on CT scan data of 6 healthy volunteers. There were 5 males and 1 female with an average age of 24.2 years (range, 23-25 years). There were 3 left knees and 3 right knees. According to the CPAK typing method, the knees were rated as types Ⅰ to Ⅵ. Under the same material properties, boundary conditions, and axial loading, biomechanical simulations were performed on the finite element model of the knee joint. Based on the Von Mises stress nephogram and displacement nephogram, the peak stresses of the meniscus, femoral cartilage, and tibial cartilage, and the displacement of the meniscus were compared among different types of knee joints. Results The constructed finite element model of the knee joint was verified to be effective, and the stress and displacement results were consistent with previous literature. Under the axial load of 1 000 N, the stress nephogram showed that the stress distribution of the medial and lateral meniscus and tibial cartilage of CPAK type Ⅲ knee joint was the most uneven. The peak stresses of the lateral meniscus and tibial cartilage were 9.969 6 MPa and 2.602 7 MPa, which were 173% and 165% of the medial side, respectively. The difference of peak stress between the medial and lateral femoral cartilage was the largest in type Ⅳ knee joint, and the medial was 221% of the lateral. The displacement nephogram showed that the displacement of the medial meniscus was greater than that of the lateral meniscus except for types Ⅲ and Ⅵ knee joints. The difference between medial and lateral meniscus displacement of type Ⅲ knee joint was the largest, the lateral was 170% of the medial. Conclusion In the same type of joint line obliquity (JLO), the medial and lateral stress distribution of the knee was more uniform in varus and neutral positions than in valgus position. At the same time, the distal vertex of JLO subgroup can help to reduce the uneven medial and lateral stress distribution of varus knee, but increase the uneven distribution of valgus knee.
ObjectiveTo investigate the feasibility and mechanical properties of polymethyl methacrylate (PMMA) bone cement and allogeneic bone mixture to strengthen sheep vertebrae with osteoporotic compression fracture.MethodsA total of 75 lumbar vertebrae (L1-L5) of adult goats was harvested to prepare the osteoporotic vertebral body model by decalcification. The volume of vertebral body and the weight and bone density before and after decalcification were measured. And the failure strength, failure displacement, and stiffness were tested by using a mechanical tester. Then the vertebral compression fracture models were prepared and divided into 3 groups (n=25). The vertebral bodies were injected with allogeneic bone in group A, PMMA bone cement in group B, and mixture of allogeneic bone and PMMA bone cement in a ratio of 1∶1 in group C. After CT observation of the implant distribution in the vertebral body, the failure strength, failure displacement, and stiffness of the vertebral body were measured again.ResultsThere was no significant difference in weight, bone density, and volume of vertebral bodies before decalcification between groups (P>0.05). After decalcification, there was no significant difference in bone density, decreasing rate, and weight between groups (P>0.05). There were significant differences in vertebral body weight and bone mineral density between pre- and post-decalcification in 3 groups (P<0.05). CT showed that the implants in each group were evenly distributed in the vertebral body with no leakage. Before fracture, the differences in vertebral body failure strength, failure displacement, and stiffness between groups were not significant (P>0.05). After augmentation, the failure displacement of group A was significantly greater than that of groups B and C, and the failure strength and stiffness were less than those of groups B and C, the failure displacement of group C was greater than that of group B, and the failure strength and stiffness were less than those of group B, the differences between groups were significant (P<0.05). Except for the failure strength of group A (P>0.05), the differences in the failure strength, failure displacement, and stiffness before fracture and after augmentation in the other groups were significant (P<0.05).ConclusionThe mixture of allogeneic bone and PMMA bone cement in a ratio of 1∶1 can improve the strength of the vertebral body of sheep osteoporotic compression fractures and restore the initial stiffness of the vertebral body. It has good mechanical properties and can be used as one of the filling materials in percutaneous vertebroplasty.
Objective The biomechanical characteristics of three internal fixation modes for femoral subtrochanteric spiral fracture in osteoporotic patients were compared and analyzed by finite element technology, so as to provide the basis for the optimization of fixation methods for femoral subtrochanteric spiral fracture. MethodsTen female patients with osteoporosis and femoral subtrochanteric spiral fractures caused by trauma, aged 65-75 years old, with a height of 160-170 cm and a body weight mass of 60-70 kg, were selected as the study subjects. The femur was scanned by spiral CT and a three-dimensional model of the femur was established by digital technology. The computer aided design models of proximal intramedullary nail (PFN), proximal femoral locking plate (PFLP), and the combination of the two (PFLP+PFN) were constructed under the condition of subtrochanteric fracture. Then the same load of 500 N was applied to the femoral head, and the stress distribution of the internal fixators, the stress distribution of the femur, and the displacement of femur after fracture fixation were compared and analyzed under the three finite element internal fixation modes, so as to evaluate the fixation effect. ResultsIn the PFLP fixation mode, the stress of the plate was mainly concentrated in the main screw channel, the stresses of the different part of the plate were not equal, and gradually decreased from the head to the tail. In the PFN fixation mode, the stress was concentrated in the upper part of the lateral middle segment. In the PFLP+PFN fixation mode, the maximum stress appeared between the first and the second screws in the lower segment, and the maximum stress appeared in the lateral part of the middle segment of the PFN. The maximum stress of PFLP+PFN fixation mode was significantly higher than that of PFLP fixation mode, but significantly lower than that of PFN fixation mode (P<0.05). In PFLP and PFN fixation modes, the maximum stress of femur appeared in the medial and lateral cortical bone of the middle femur and the lower side of the lowest screw. In PFLP+PFN fixation mode, the stress of femur concentrated in the medial and lateral of the middle femur. There was no significant difference in the maximum stress of femur among the three finite element fixation modes (P>0.05). The maximum displacement occurred at the femoral head after three finite element fixation modes were used to fix subtrochanteric femoral fractures. The maximum displacement of femur in PFLP fixation mode was the largest, followed by PFN, and PFLP+PFN was the minimum, with significant differences (P<0.05). ConclusionUnder static loading conditions, the PFLP+PFN fixation mode produces the smallest maximum displacement when compared with the single PFN and PFLP fixation modes, but its maximum plate stress is greater than the single PFN and PFLP fixation mode, suggesting that the combination mode has higher stability, but the plate load is greater, and the possibility of fixation failure is higher.
This study aims to establish a multi-segment foot model which can be applied in dynamic gait simulation. The effectiveness and practicability of this model were verified afterwards by comparing simulation results with those of previous researches. Based on a novel hybrid dynamic gait simulator, bone models were imported into automatic dynamic analysis of mechanical systems (ADAMS). Then, they were combined with ligaments, fascia, muscle and plantar soft tissue that were developed in ADMAS. Multi-segment foot model was consisted of these parts. Experimental data of human gait along with muscle forces and tendon forces from literature were used to drive the model and perform gait simulation. Ground reaction forces and joints revolution angles obtained after simulation were compared with those of previous researches to validate this model. It showed that the model developed in this paper could be used in the dynamic gait simulation and would be able to be applied in the further research.
Objective To investigate the effect of Navio robot-assisted unicompartmental knee arthroplasty (UKA) on the biomechanics of knee joint during sitting-up movement, and to determine whether UKA can maintain the biomechanical characteristics of knee joint. Methods The clinical data of 8 patients with medial compartment osteoarthritis treated with medial fixed platform of Navio robot-assisted UKA between January 2018 and January 2019 and had the complete follow-up data were retrospectively analyzed. There were 4 males and 4 females; the age ranged from 58 to 67 years, with an average of 62.3 years. The disease duration was 6-18 months, with an average of 13 months. The varus deformity ranged from 4° to 6°, with an average of 5°; the knee flexion range of motion was 0°-130°, with an average of 110°. All patients had no extension limitation. The imaging data of bilateral knees during sitting-up movement were collected by biplane C-arm X-ray machine at 3 weeks before operation and 7 months after operation. The three-dimensional models of femur and tibia were established by dual-energy CT scanning, and the three-dimensional models of femur and tibia were matched and synchronized with the femur and tibia in X-ray film by automatic matching tracer software. The biomechanical parameters of femur and tibia were measured, including internal rotation/external rotation, varus/valgus, forward/backward displacement of medial and lateral tibia contact center, and lateral compartment joint space. Results Eight patients were followed up 5-7 months, with an average of 6.4 months. In the comparison of the affected side before and after operation, except for the difference of varus/valgus which was significant (t=4.959, P=0.002), the differences in other indicators was not significant (P>0.05). There were significant differences in varus/valgus and internal rotation/external rotation between healthy and affected sides at 3 weeks before operation (P<0.05), and the differences in other indicators was not significant (P>0.05). At 7 months after operation, the difference in the forward and backward displacement of medial tibia contact center was significant (t=3.798, P=0.007), and the differences in other indicators was not significant (P>0.05). Conclusion UKA can effectively correct the varus and valgus of the knee joint, and restore the rotational biomechanical characteristics of the affected knee joint. It does not affect the establishment of the lateral compartment joint space, but the medial and lateral tibia contact center still changes.
Objective To investigate the feasibility of anterolateral approach for L5 vertebral resection, bone grafting, and screw rod fixation by imaging and biomechanics researches. Methods Twenty formalized adult cadavers (12 males and 8 females) were randomly divided into 2 groups; L5 vertebral resection, bone graft, and screw rod fixation was performed on 10 specimens by using anterolateral approach (experimental group), and on the other 10 specimens by combined anterior and posterior approach. CT scanning and three-dimensional reconstruction were performed in the experimental group; preoperative maximal safe entry angle and depth of screws and intraoperative actual entry angle and depth of screws were measured; the sacral screw position was observed after operation. The biomechanical test was done in 2 groups. Results Twenty specimens smoothly underwent L5 excision and reconstruction. CT scan showed that there was no significant difference in maximal safe entry angle and depth of screws between males and females in experimental group before operation (P>0.05); the maximal safe entry angle and depth were 51.93° and 47.88 mm for anterior screw, and were 37.04° and 46.28 mm for posterior screw. After operation, depth of the sacral anterior and posterior screws were appropriate, which did not pierce into the spinal canal. The biomechanical test results indicated that the flexion, extension, and lateral flexion displacements, and vertical compression stiffness showed no significant difference between 2 groups (P>0.05). Conclusion For L5 lesions not invading posterior column, to use L5 vertebral resection, bone graft, and screw rod fixation by anterolateral approach is a safe and feasible method to reconstruct lumbosacral stability, with the advantages of no changing posture, less operation time and incision, and prevention of bone graft shift, but effectiveness need further be identified.